Hex Nuts (Including Heavy Hex Nuts)
Kep
Nuts are
hex head nuts with a pre-assembled, free spinning
external tooth lockwasher. Eliminates the need for
separate nut-side washers.
Tee
Nuts are internally threaded barrel-shaped fasteners
with 3, 4 or 6 prongs extending from a flat base.
Primarily used for fastening metal to wood, particle
board or plastic products, Tee-nuts put steel threads
into pre-drilled wood without counter boring.
Wing
Nuts have wing a shaped protrusion designed for speed
and convenience that are tightened and loosened by
hand. Wing nuts are ideal in speedy marine applications
where it is harder to use tools in any kind of intricate
work on the open sea.
Panel
Nuts are designed to be thin with the width diameter
close to the diameter of the fastener they are
securing. Hexagonal or round panel nuts are chamfered
on all surfaces, have no cutoff burs and are free of
slivers and flakes. Panel nuts provide a low profile and
are used in light duty applications.
Acorn
Nuts
have a crown, or dome,
covering. Since they have a closed top, Acorn Nuts are
chosen for safety reasons, to cover protruding threaded
mating parts, and for decorative improvement.
Flange
Nuts have flat and serrated designs designed to act as
an integrated, non-spinning washer, eliminating the need
for a separate washer. Serrated flange nuts are
fabricated with a
built in serrated washer that resist
loosening due to vibration.
Square
Nuts and Hex Square Nuts have
four equal sides. These nuts have a flat bottom side and
a chamfered top-side and can be used in a channel
or welded in place. Square nuts are still common, but
widely replaced by Hex nuts.
Call for Immediate Quote … (713) 937-4088
(866) 895-0627
Heavy
Hex Nuts are the strongest of all comparably graded
designs, both thicker and wider across the flats than
standard finished hex nuts of the same size.
They are available in a
variety of grades and the heavy pattern is typically
used for large diameter and high strength bolts.
Heavy hex nuts
have a
greater length of thread engagement and better
resistance to stretching or widening.
Slotted
Hex Nuts
have opposed slots cut into the top of the hex nut
through the center of flats. Slots are cut into the
non-bearing surface of the nut. Used for general purpose
fastening and locking, slotted hex nuts can be used with
cotter pins or safety wire through the slots and through
the hole drilled shank of the fastener.
Finished
Hex Nuts are the most common and versatile hex nut
design. Offered in a multitude of materials and
finishes, Finished Hex Nuts can be used in almost every
application.
Rod
Coupling Nuts are used to join two externally threaded
objects, usually threaded rod, together. Reducing
Coupling Nuts are available to couple two or more studs
of different diameters together.
Machine
Screw Nuts are used with smaller machine screws under ¼
inch and available with either a hex or square head.
These
four or six-sided fasteners feature a flat top and
chamfered corners with Unified, Class 2B, UNC or UNF
Series threads.
Nylon
Insert Locknuts have a nylon ring that when tightened on
a bolt, resists loosening under all types of vibrations
and torque. U-Bolt-It nylon insert locknuts are
available in a variety of sizes and materials including
low and medium carbon, heat treatable steel grades,
including non-ferrous materials.
Choosing the right fastener material is important when applications call for differences in strength, brittleness, corrosion resistance, galvanic corrosion properties, and cost.
Large or small, whatever your project or application, you can count on U-Bolt-It to provide the highest quality products at the best prices! Contact your U-Bolt specialist today at (713) 937-4088.
Call for Immediate Quote … (713) 937-4088
(866) 895-0627